Kuryakyn Pilot Pegs With Offset Mounts 1-1/4inch Clamps Chrome

Kuryakyn Pilot Pegs With Offset Mounts 1-1/4inch Clamps Chrome (Part #4436)

If you are a taller rider or just get bad leg cramps on long highway runs, your stock pegs are letting you down. Bolting on the Kuryakyn Pilot Pegs With Offset Mounts 1-1/4inch Clamps Chrome is the easiest way to fix your foot positioning and get your ride comfort back. Regular crash bar pegs just stick straight out, which locks your knees into one stiff position. This kit comes with an offset arm so you can pull the pegs closer to your boots or swing them way out forward. It gives you a custom setup that stops hip and knee pain before it even starts.

The look is clean and uses a mirror chrome finish that blends right in with any traditional cruiser or custom touring build. The Kuryakyn Pilot Pegs With Offset Mounts 1-1/4inch Clamps Chrome box includes everything you need to mount them onto your bike's front engine guard bar. It is a solid, heavy-duty upgrade that looks great when parked and makes a huge difference the second you hit top gear on the interstate. Adding the Kuryakyn Pilot Pegs With Offset Mounts 1-1/4inch Clamps Chrome to your frame means your next long road trip won't leave you sore.(Note: This is a single chrome variant. It is sold as a complete pair with both left and right sides, clamps, and hardware included in one box).

Features and Benefits

Spin It 360 Degrees

The best part about the Kuryakyn Pilot Pegs With Offset Mounts 1-1/4inch Clamps Chrome is the adjustable offset arm. You can swing the mount completely around the crash bar line. Pull them back if you have shorter legs, or push them way up front if you want extra room to stretch your joints out on long highway miles.

Kills Engine Buzz

The footpads use thick, deeply grooved pads made from real EPDM rubber. This specific rubber layout is built for one job: killing high-frequency engine vibrations before they get into your boots. Your feet won't go numb after an hour of riding, and the rubber won't dry out or crack from the sun.

Clamps Hold Tight

The kit uses heavy, two-piece 1-1/4-inch clamps that wrap around your engine guard tubes. Cheap unbranded mounts will slide down or twist when you stand up or put your full weight on them. These premium mounts lock down completely solid so your pegs never slip while you are on the road.

Tough Chrome Finish

The whole setup has a thick chrome plating over the metal housing. It is made to take hits from road dirt, rain, and motor heat without peeling, flaking, or rusting out. Keeps the lower part of your bike looking sharp.

Vehicle Fitment Guide

The Kuryakyn Pilot Pegs With Offset Mounts 1-1/4inch Clamps Chrome kit is a universal design made to clamp onto standard engine guard tubing sizes.Universal Bar Fit: Fits any bike with 1-1/4 inch (32mm) front engine guards, crash bars, or highway bars. This covers most Harley-Davidson Touring, Softail, and Trike frames, along with Indian, Honda, Yamaha, Kawasaki, and Suzuki cruisers using 1-1/4 inch tubes.Fitment Warning: These will NOT fit smaller 1-inch bars or oversized 1-1/2-inch bars. Take a tape measure to your crash bars to check the outside diameter before ordering to make sure it is exactly 1-1/4 inches.

Frequently Asked Questions (FAQ)

Do I get both sides or just one?

You get both. The Kuryakyn Pilot Pegs With Offset Mounts 1-1/4inch Clamps Chrome kit ships out as a complete matching pair. You get two pegs, two offset arms, and two clamps inside the factory box.

Do I need to buy extra bolts or adapters to put them on?

No. This is a total standalone kit. It comes with all the hardware and bolts you need to mount the assemblies directly onto a 1-1/4 inch bar right out of the box.

Can I fold the pegs up out of the way when riding in town?

Yes. The pegs have a built-in pivot hinge. You can flip them up vertically against the arms when you are splitting lanes, parking in a tight garage, or riding solo without using them.

Are there black versions or different clamp sizes for this part number?

No. Part number 4436 is a single product variant. It only comes in Chrome with the 1-1/4 inch mounting clamps.